Skip to content
Find The Needle
Powered by Pagefind
Find The Needle guides

Find The Needle water, pumps and pipes guide

Raise water 10 m with a well, 20 m with Pipe Pump Mk.1 and 50 m with Mk.2, then read pressure and flow at the water plate in Find The Needle.

Practical guide

Heights, parts and the water plate follow the launch changelog and patch V15.4 (November 2026). Pipe prices and exact per-machine water demand are only shown in game.

11/11/2026 Last updated: 11/11/2026 4 min read
Factory machines and pipework around the hay pile in Find The Needle
Water runs on its own network, with its own limits. Image © Needless Games. Image source

FAQ

How high can I pump water?
A well reaches ten metres on its own. Cut a Pipe Pump Mk.1 into the main to add twenty metres, or a Mk.2 to add fifty, and the pump pushes either way round.
Why is my machine glowing blue?
It has no water. Check the pipe run down to the pump, and read the machine's status line, which states how much water it needs per minute.
What does E do at a pipe?
At a sight glass or on a pump it opens the water plate, showing pressure and flow plus a pressure-radius overlay. It does not touch power there.

Why does water matter?

Because two machines that hold a stage together run on it. The Sugar Cooker cooks bales and water into sugar sacks, and the Biogas Digester turns wrapped bales into power — and both complain loudly when the water stops. The Gas Plant counts down too when no water arrives.

Water arrives with the same order that opens the first of them: Borehole Pump, water pipes, Biogas Digester and the movable Selling Stand all open with The Dairy.

How far can water travel?

Part What it adds Notes
Well / Borehole Pump Pushes water 10 m up The base of the network
Pipe Pump Mk.1 +20 m Cut it into a main; pushes either way round
Pipe Pump Mk.2 +50 m Same rule, more head
Valve Caps the flow For splitting demand between machines
Water Cross Four-way junction Joins runs without a dead end
Underground pipe Runs under the floor Chains with other pieces
Pipe through a platform Vertical run Goes straight through, like lifts

When a machine sits above the reach, it says it is dry and how far out of reach it is, and the pipe view draws a ring where the water stops climbing. That number is the instruction: add another pump, or move the machine down.

How do I read pressure and flow?

Press E at a pipe’s sight glass or on a pump to open the water plate. It shows pressure and flow, and it has a SHOW PIPE PRESSURE RADIUS overlay that draws the area the current pressure can serve.

Two reading rules:

  1. Pipes show water, not numbers. You judge a line by what is moving inside it, and by the machine’s own litres-per-minute figure.
  2. A ring is a limit, not a suggestion. If a machine sits outside the radius, no amount of pipe will fix it — you need head.

What breaks, and what it looks like

Symptom Meaning Fix
Machine glows blue No water reaching it Trace back to the pump; check valves and the sight glass
Machine says it is dry and by how much It is above the network’s reach Add a pump stage or lower the machine
Biogas Digester counting down It is burning bales faster than water or feed arrives Fix the feed first, then the water
Gas Plant counting down No water in Same trace, different machine
Whole pump chain dry after a power blip Fixed: a short power cut no longer dries a chain Fixed in the launch build; any current build already has it

How should the pipe run be laid out?

Water is a vertical problem, so plan the riser before the machines that need it.

  1. Put the well where you will build upward, not in a corner you will pave over.
  2. Run one main, with valves at each branch rather than a mesh of parallel lines.
  3. Keep pump access clear. You will press E on them, and a pump behind a press line is a pump you cannot read.
  4. Use the water plate before you add a machine, so you know the pressure radius already covers the spot.
  5. Mark the run with the Customizer’s pipe colours if the yard has more than one line — the same colour trick that works for splitter routes (splitter routes).

Water and power are separate networks with separate failures: a factory can be fully powered and still have half its production glowing blue. The power side is on conveyors and power and power priority.

Which machines need water?

The changelog names the Sugar Cooker’s recipe (bales and water) and the two burners that count down without it. It does not publish a table of every machine’s demand, so read each machine’s panel: it states its requirement in litres a minute.

If a stage stalls for no obvious reason, check water before you rebuild a belt (troubleshooting). The stage that introduces water is on production stages, and the machines themselves are in the machines index.

Related Articles

Was this helpful?