Find The Needle power priority and overclocking
Set machines to FIRST, NORMAL or LAST so a short grid fails in the right order, run them from 1% to 100%, and push past 100% with a Needle Socket.
Priority levels, overclock range and generator numbers follow the launch changelog and patches V15.4 and V16.4 (November 2026). Overclock's effect on throughput per percent is not published.
What does PRIORITY do?
It decides which machines lose power when a line cannot serve everything. Set each machine to FIRST, NORMAL or LAST, and when the line runs short the LAST machines switch off first.
That turns a blackout from an accident into a plan: the packaging line that feeds an order can be FIRST, the decorative press you are testing can be LAST, and a fuel hiccup costs you the experiment instead of the delivery.
How should I assign priorities?
| Machine | Priority | Reason |
|---|---|---|
| Generators’ own fuel chain, water pumps | FIRST | Nothing works downstream without them |
| Machines on the current order | FIRST | The order is the money and the stage gate |
| Sell-stand line | NORMAL | Income, but not a deadline |
| Scanner gates | NORMAL or higher | A bypassed gate loses finds |
| Experimental line, decoration, spare press | LAST | First to go, by design |
Two rules of thumb: never put a water pump on LAST (a dry Biogas Digester takes time to recover), and never put two machines that feed each other on different priorities unless you want the pair to thrash.
How do I read the grid?
Every generator and pole has a POWER tab with a graph of what each line made and wanted; the Switch Box shows the same lines, and machines report whether they are running and how much they draw. SHOW POWER LINE lights everything on one line and labels the machines on it, which is the fastest way to find what is actually on the circuit you are about to overload.
The tab also says why a line is short. That sentence is worth more than the graph: it separates “no capacity” from “nothing connected”.
V16.4 made the numbers honest. Power cards now show the real output with tuning and needles applied instead of the base figure, the generator panel names what boosts it and the total boost, and the spare-power graph works again. Overclocking is the case that needed it: a machine pushed past 100% with a needle socket draws and produces something the base card never showed.
What is overclocking?
A machine can run anywhere from 1% to 100%. Lower it to save power and inputs, or run it flat out when the belt behind it can keep up.
The interesting case is above 100%: put a needle in a Needle Socket and the machine can be pushed past its normal ceiling. That is how a yard with a modest generator bank gets more out of the machines it already owns instead of building another line.
| Setting | Use it when |
|---|---|
| 1–50% | Input is scarce, or you want a slow trickle into a Depot |
| 100% | Default; the machine matches its design rate |
| Above 100%, with a socket | Power is cheap and space is not |
Both the Needle Socket and the shed’s other utility cards cost money only on V15.4 — no parts — so overclocking is available earlier than its late-game sound suggests.
What is the cheapest power on V15.4?
| Item | Cost / output |
|---|---|
| Electricity connection | $30 |
| First Hay Generator | $60 |
| Second Hay Generator | $80 |
| Third and later | Pre-V15.4 price |
| Generator level 1 upgrade | $15 |
| Stronger generator levels | 10–15 kW |
| Panel Press draw | 1 kW (was 5) |
| Smelter draw | 4 kW (was 8) |
| Depot Drone Mk I draw | 0.5 kW (was 2.5) |
Two generators burn things other than hay: the Biogas Digester turns wrapped bales into power and warns when it burns faster than it is fed, and the Gas Plant burns fuel discs. A generator also warns while its fuel is running low, rather than after it is empty, and a line that goes short plays a power-down sound.
One card on the same theme: the Wider Rake Head now shows how much more power your rakes will use, and warns you when the line cannot pay for it — worth reading before you buy it on a marginal grid.
How do I cut one machine without killing the yard?
Run a cable by hand from a pole to join or cut a single machine. Wall Outlets and Double Wall Outlets route cable along walls, through platforms and through roofs, and pole reach counts height, so a cable can climb.
Do not use E for this. E on a pole shuts down the entire network (conveyors and power).
What does a short line look like in practice?
- Machines show SHORT OF POWER on their panels.
- The POWER tab’s line graph shows demand above supply.
- LAST-priority machines switch off first; the rest keep running slower than you expect.
- A fuel-starved generator warns before it dies, and the Digester or Gas Plant counts down when water or feed stops (water and pipes).
Fix capacity before you fix layout: a bigger generator costs less than rebuilding the line that browned out. The rest of the stop-go checklist is on troubleshooting, and the overclocking economics sit alongside the upgrade prices on tech tree.
Related Articles
guides
Find The Needle blueprints and Dismantle Mode
Save a Find The Needle build on a Blueprint Designer pad, copy it anywhere, and use the Needle Hammer to take it down with the refund shown first.
guides
Find The Needle day, night and lighting
Nights are brighter since V14.1 and Options has a brightness slider, but lamps, flood lights and a Light Sensor still pay for themselves in Find The Needle.
guides
Find The Needle Depot and Depot Drone guide
How the Find The Needle Depot stores parts, what KEEP UP TO and Shelf Limits do, and how Depot Drones carry 3, 6 or 12 loads to the lorry.
Was this helpful?
Thanks for the feedback!