Skip to content
Find The Needle
Powered by Pagefind
Find The Needle guides

Find The Needle controls and keybinds

The Find The Needle keys that change a build: F for No Snap, E on a pole, R to rotate, Ctrl+Z to undo a dismantle, and Ctrl+C and Ctrl+V to copy settings.

Reference

Keys are transcribed from the Early Access announcement and the patch notes up to V16.4 (November 14, 2026), not from a hands-on test. The game's own Controls screen is the final authority after any patch.

11/2/2026 Last updated: 11/16/2026 6 min read
First-person view of the yard with a hand tool beside the hay pile
Most of the build runs on a handful of keys. Image © Needless Games. Image source

FAQ

What key turns conveyor snapping off?
F toggles No Snap Mode. It stays on until you press it again, so the pieces you place after it are hand-aligned too.
What does E do on a power pole?
It shuts down the whole electricity network, not one machine. At a pipe sight glass or on a pump the same key opens the water plate instead.
Is there a key to reverse a conveyor belt?
No. Remove the segment and place it again pointing the other way, or use a splitter route to send the flow elsewhere.
How do I place a part in exactly the right spot?
Hold H to pin the piece, then nudge it with the arrow keys before you confirm the placement.
Is there an undo for dismantling?
Yes, since V16.4: Ctrl+Z in Dismantle Mode puts back the last 20 things you took down.
Does the game support a controller?
Steam lists three features for the full game — single-player, achievements and Family Sharing — and no controller support. Players have asked for pad support on the discussion board without an answer, so it is unlisted rather than refused.

Which keys matter most?

Eight keys cover most of a build, and the rest is click and aim.

Key What it does The mistake it causes
F Toggles No Snap Mode for belts and parts Left on, so every later piece is hand-aligned
E On a power pole: shuts down the whole network. At a pipe sight glass or pump: opens the water plate Pressed to “fix” one machine, kills the yard
R Rotates the piece you are placing; in Dismantle Mode, takes the whole blueprint Turned past the angle you wanted
Ctrl+Z In Dismantle Mode, puts back the last 20 things you took down Not knowing it exists, and rebuilding by hand
Ctrl+C / Ctrl+V Copies and pastes machine settings while you look at a machine Retyping a splitter or press setup on every copy
H Holds a piece in place so the arrow keys can nudge it; with the vacuum equipped, it is the vacuum hose Nudging without pinning, so the piece follows the mouse
Alt + number Turns hotbar pages Hunting a card that was on another page
Esc Pauses the yard Pausing mid-build and losing track of a half-placed line

Movement, jumping and interaction follow the usual first-person defaults. If a key does nothing, the first check is still the game’s own Controls screen — the paid build has taken five announced patches since launch (patch notes).

F is a toggle, not a tap

F exists so you can place one conveyor exactly where you aimed instead of where automatic snap wants it. It does not reset itself: place the awkward corner, then press F again.

Two checks after any F-placed run:

  1. Walk a few loads across the joint. Hand-aligned does not mean connected.
  2. Watch the preview before confirming. Snap shows the neighbour it will attach to; No Snap Mode does not.

The surrounding behaviour is on conveyors and power.

E is a network switch — or a water gauge

On a power pole, E takes down the whole network. On a pipe’s sight glass or on a pump, the same key opens the water plate, which shows pressure and flow plus a pressure-radius view (water and pipes).

Use it deliberately: before dismantling anything on a live line, and before rebuilding a route that is still moving product. Afterwards, restore the supply at the pole and watch whether the shortage warning clears. If the yard stays dark after that, the fault is upstream of the pole (troubleshooting).

R rotates, and R takes the whole blueprint

While placing, R rotates in fixed steps rather than free angles. Confirm with left click once the preview points where you want.

In Dismantle Mode the mapping flipped on V16.4. Aiming at a blueprint piece and holding now takes just that piece, and R switches to the whole blueprint — the reverse of the V15.4 behaviour. The pointer tells you which one is armed, so read the hint before you commit, and press Ctrl+Z if you guessed wrong (blueprints and dismantling).

Ctrl+Z and Ctrl+C

Ctrl+Z works inside Dismantle Mode and restores the last 20 removals, including a refused dismantle that used to break the undo stack. It is the fastest fix for taking down the wrong end of a line.

Ctrl+C and Ctrl+V copy settings from the machine you are looking at and paste them onto the next one — also available as buttons on the machine panel. Pasting settings onto a Hay Silo no longer switches it off.

H pins a part, or runs the vacuum

H holds the piece you are placing in place so the arrow keys can nudge it — the usual fix for a port that is one grid square out. With the vacuum hose equipped, H instead sprays whatever the vacuum holds toward where you point.

The rest of the keyboard

Key Action Notes
Y Emote wheel Thumbs up, point, rock on, a cup of tea, spitting, and a couple more
P Photo mode Freezes the view for screenshots
L Flashlight Bought over the Supply Co counter
F1 Sandbox tools Sandbox runs only; those runs stay off the leaderboards

Nights are brighter than at launch, and Options has a Night brightness slider next to Always day — 50% is the normal night (lighting).

Is there controller support?

Not that Steam lists. The store’s feature list for the full game carries exactly three entries — Single-player, Steam Achievements and Family Sharing — and no controller row, which is why this page documents keys rather than pads. That is “not listed”, not a statement that a pad will never work.

What players do report, repeatedly, is the gap itself: threads asking about Xbox pads, PlayStation pads, Steam Deck controls and a controller that stopped responding after an update have sat on the Steam discussion board with no developer answer. If a pad is how you want to play, treat it as an open question until the store adds a row.

When a key does nothing

  • You are aiming at nothing placeable. The preview stays red and the key does nothing until the target is valid.
  • You are too far from the pole, machine or pipe. Interaction needs you in front of it.
  • A menu or the build catalogue has focus. Close it and the world keys work again.
  • You are pressing a mod key without the mod. The savegame editors on Steam Workshop add their own binds; the base game does not answer to them.

The first-hour order for these keys is in the beginner guide.

Related Articles

Was this helpful?